ROLL-A-LINE™ is a finishing line marking paint for interior and exterior tarmac, concrete and painted surfaces. Can be used for:

• Roadline Marking;
  

• Runway Lines Marking;
  

• Parking Bay Marking;
  

• Factory and Warehouse Floor Lines;
  

• Factory and Warehouse Safety Lines;
  

• Etc.

All above technical data are based on ROLL-A-LINE™. Coverage / spreading rate of colours depend on condition and porosity of the surface and the manner in which ROLL-A-LINE™ is applied and used.

• TYPE  -  Acrylic Copolymer Emulsion;
  

• DRYING TIME  -  Surface: 1/2 - 1hour (23° Celsius and 50% Relative Humidity);
  

• HARD DRY  -  3 - 4 hours (at 23° Celsius and 50% Relative Humidity);
  

• OVERCOATING  -  4 Hours;
  

• VISCOSITY  -  100 - 104 KU;
  

• SPECIFIC GRAVITY  -  1.23 - 1.27;
  

• FINISH  -  Low Sheen;
  

• WEIGHT SOLIDS  -  44 - 49%;
  

• VOLUME SOLIDS  -  34 - 46% (100u wet film will give 35u dry film);
  

• SPREADING RATE  -  7 - 10 m²/litre (to obtain a continuous film without full coverage;
  

• COVERAGE (THEORETICAL)  -  70m - 80m x 100mm running meters/liter;
  

• FLASH POINT  -  Not applicable;
  

• COLOUR RANGE  -  Available in White, Yellow, Blue, Black, Red and custom colours;
  

• PACKING SIZE  -  1 Liter, 5 Liters and 20 Liters.
  

Coverage / spreading rate of colours depend on condition and porosity of the surface.

• READY  -  for use with brush or roller;
  

• SPRAY  -   Apply only with large nozzle – minimum 2,4mm or air-less system;
  

• THINNING  -  Only up to 10% water if really necessary;
  

• EQUIPMENT CLEANING  -  Water.
  

Clean thoroughly by removing all foreign matter with a wire brush, hosing down with water and using a clean hard bristle broom to remove all loose particles, dust and dirt.

• Allow to dry;

• Apply two coats of ROLL-A-LINE™ Paint allowing at least 4 hours drying time between coats;

• Allow at least 4 hours drying time between coats;

• Allow to dry and overcoat with one coat of ROLL-A-LINE™ Paint undiluted.

It is recommended that existing surfaces are washed with a high pressure machine and an Anti-Fungicidal Wash. Any sign of fungal growth must be removed by treating with Anti-Fungicidal Wash before painting:

• Wash down with water or detergent to remove all dirt, grease and paint other contaminants;
  

• Allow to dry;
  

• Apply one coat of ROLL-A-LINE™ paint if surface is in sound condition;
  

• Apply second coat of ROLL-A-LINE™ paint for change of colour, allowing at least 4 hours drying time between coats.

• Do not apply direct to new galvanised iron, sand blasted steel or aluminium;
  

• Application to areas where temperature exceeds 60° Celsius is not recommended;
  

• Application to cold surfaces below 10° Celsius is not recommended;
  

• Pre-wet new asbestos surfaces before painting;
  

• For diluting use water only if required;
  

• Do not use Mineral Turpentine, Lacquer Thinners or Methelated spirits for diluting as this will alter or destroy the quality and performance of ROLL-A-LINE™;
  

• Clean all equipment and tools with water after use;
  

• Do not apply to roofs which are used for the collection of drinking water use;
  

• Clean all equipment and tools with water after use.

• The ambient temperature must be between 5ºC and 35ºC and humidity between 10% and 85%;

• Do not paint too early as the wall may still be damp - paint only when the surfaces are dry;

• Do not paint in too hot weather, rather paint early morning and after lunch, the slower the paint dries, the longer it lasts;

• Excessive application thickness and/or rapid drying could lead to cracking;

• Avoid applying under adverse weather conditions as this could result in poor product performance;

• Excessively friable surfaces should be cleaned down prior to primer application;

• To assure smooth surface, paint corner to corner - from top to bottom - never halfway up and half way down;

Painting is a relatively user-friendly activity if the proper precautions are taken to ensure safety

• It is advisable to wear gloves as ROLL-A-LINE™ is difficult to remove from skin;

• Always keep out of reach of children and animals;

• Do not take in orally - harmful if swallowed. Seek medical attention and do not induce vomiting;

• If accidental contact with skin, wash immediately with soap and water or a good quality skin cleaner;

• If accidental contact with eyes, rinse immediately with plenty of water and seek medical advice;

• Wear a respirator if the area being painted cannot be adequately ventilated, and work for short periods only;

• Ventilate the area to be painted, opening all doors and windows and using fans during application and drying;

• Protect floors with cloth Drop Cloths, not plastic, which is far more slippery;

• Do not paint or store paint near any heat source such as a water heater or fireplace, and never smoke while painting;

• Make sure your ladder is in good shape. Set the legs on an even surface and lock the cross braces. Do not stand on the top of the ladder nor on the utility shelf. If you are having difficulty reaching a spot, get down from the ladder and move it rather than leaning out;

• Clean up carefully and thoroughly when you are done for the day;

• If rags have alkyd paint or thinner on them, leave them to dry outside to avoid any chance of spontaneous combustion;

• Choose an area inaccessible to children and pets, and when they are thoroughly dry, take them to a toxic-waste dump site.

Different surfaces and environmental conditions require specific painting systems to produce the best possible results - It is, therefore, recommended that you contact a representative from Classic Paints for advice on all your painting requirements, whenever possible.

The information, and, in particular, the recommendations relating to the application and end-use of Classic Paints products, are given in good faith based on Classic Paints’ current knowledge and experience of the products when properly stored, handled and applied under normal conditions. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the Product Data Sheet for the product concerned, copies of which will be supplied on request.

01/07/2022 - This supercedes all previous publications - This technical data furnished is obtained from controlled laboratory tests under ideal application conditions. No guarantee of any performance characteristic is given or implied and we do not hold ourselves responsible for any consequential damage of whatsoever nature that may arise from use of our products. In the event of a proven product fault our liability will be limited to the replacement of the product only. It is the users responsibility to confirm the currency of product data sheets.